Suggested Site

Everyone has got their own unique perception about How to Install a Bathtub Yourself.

Installing a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably hard task. If the old bathtub is easily easily accessible, the task can relocate rapidly; if you have to open a wall surface to get rid of the old tub and position the brand-new bath tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will need an assistant to leave the old tub and also set in the brand-new one. Make certain you have qualified yourself for the task and fit attempting it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to consider using one before you start. Chances are you may need an expert plumber to make tube links.
This write-up will help you install a new tub in your washroom if you have actually already gotten a brand-new bathtub and don't need to alter the setup of your previous water supply pipes.
Your tools and also product checklist ought to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Installation

Firstly, the sustaining structure supplied with the bath should be fitted (if needed) according to the maker's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of both taps using 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its final position.

Removing Old Touches

If you require to change old faucets with new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather problematic because of the limited accessibility that is frequently the situation.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.

Setting up the Tub

Utilizing the two wood boards under its feet, put the tub in the required placement. The wooden boards are handy in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and also changing the feet on the bathtub until the spirit level reads degree.
To mount taps, fit all-time low of the furthest flexible faucet port to the ideal supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Switch on the supply of water as well as examine all joints and new pipework for leaks as well as tighten them if needed. Load the tub and also examine the overflow electrical outlet and the regular electrical outlet for leakages.
Finally, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and sealing around the bathtub needs to wait till the tub has been made use of a minimum of when as this will certainly resolve it into its final placement.

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin making sure that the washers remain in place between the tap and also the sink. Protect the tap in position with the manufacturer offered backnut. Once the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind must be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

Tiling Around the Bath tub

In the area where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, causing difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components and also installations. They are offered in tubes as well as cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealer can split fairly very early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and also cement.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

I hope you enjoyed reading our post on Tools You Need to Install a New Bathtub . Many thanks for finding the time to browse our article post. For those who enjoyed our blog posting plz don't forget to pass it around. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Best in business.